Multi-Functional Single to 3phase 0.1kw to 30kw Profinet Bus Servo Drives with Servo Motor

• Task: Program
• Structure: Closed-Loop
• Mathematical Model: Linear
• Signal: Continuous
• Function: Automatic Control
• Certification: ISO: 9001, CE
• Model NO.: EA180P
• Condition: New
• Customized: Customized
• Material: Aluminum Alloy
• Control Method: IGBT PWM Control Sine-Wave Current Drive
• Front Panel: 5 Keys, 5-Digit LED
• Protection Level: IP10
• Pollution Level: 2 Level
• Cooling Method: Fan Cooling
• Frequency Bandwidth: 1.2kHz (23-Bit Encoder)
• Transport Package: Wooding
• Trademark: SINEE
• Origin: China
• Production Capacity: 400000sets/Year

Product Description

EA180P  PROFINET Servo Drives

Single-phase 220V~240V 0.1~1kW
Three-phase 220V~240V 0.75~1.5kW
Three-phase 340V~460V 1.5~30kW

Product Description

High-speed response performance

•Up to 1.0KHz speed frequency response.
•Shortened positioning time.
•High-speed and high-accuracy real-time synchronous
communication on basis of parallelized system design.

High-accuracy positioning
•Encoder of 17 bit incremental and 23 bit absolute value,
with the powerful control performance, can make the
positioning accuracy less than 5 encoder pulses.

Abandant product series
•Analog & pulse standard type and network type with
EtherCATor CANopen or RS485 protocol supported;
•2500 ppr or serial type with17 bit incremental or 23 bit absolute values encoder available

Small Size
•Size similar to Panasonic A6 series drive, matched with SINEE SES servo motor, can help to minimize the system volume.

Intelligent controls
•Intelligentized resonance suppression
The system has four (4) high-frequency resonance suppression
notch filters, two (2) of them are the FFT-based ones; the others
are manual ones.
Synchronously the vibration suppression filters are provided
to minimize the vibration of long arm machine.
•Control gain switchover functions
The control loop structure on the basis of PDFF may reduce
overshooting efficiently.
The parameter self-adjustment on the basis of inertia
may enhance the site adaptability.

High reliability
•Complete protection function and EMC design
Protection function design on the basis of overall reliability of motor and driver;
EMC design on the basis of graded optimization and system adaptability.
•High-performance motor material and technology ensure the system to run reliably
Containing dysprosium-neodymium-ferroboron magnetic steel, high-strength shaft,
Tamagawa encoder, large-size bearing, encapsulated by resin.

Product Parameters

Item									Specification
Basic Specification			Control method						IGBT PWM control sine-wave current drive
			Feedback						17-bit incremental/encoder, 23-bit absolute encoder
			Six control modes						Speed control, position control, torque control, speed/position control, torque/speed control, position/torque control
			Front panel						5 keys, 5-digit LED
			Regenerative brake						Built-in brake unit and resistor; an external braking resistor can be connected
			Use conditions		Environment temperature				Working temperature 0~40° , storage temperature -20° ~85°
					Ambient humidity				Working/storage: ≤ 90%RH (without dew condensation)
					Altitude				≤ 1,000m
					Anti-vibration impact strength				Vibration: ≤ 4.9m/s² (no operation at the point of resonance is permitted), impact: ≤ 19.6m/s²
					Protection level				IP10
					Pollution level				2 level
			Cooling method						Fan cooling
Performance			Speed-torque control mode		Speed fluctuation ratio		Load fluctuation		0~100 load: Maximum 0.3%	Based on 23bit encoder, at rated speed
							Supply voltage change		At rated voltage ± 10%: Maximum 0.3%
							Environment temperature		0~50ºC : Maximum 0.3%
					Speed regulation ratio				1:5000 (17bit and 23bit encoder)	Minimal speed/rated rotating speed of con- tinuous stable operation under the rated load
					Frequency bandwidth				1.2kHZ (23-bit encoder)
					Torque control accuracy				±3% current repetition accuracy
					Soft start time setting				0~30s (acceleration and deceleration can be set respectively)
			Position control mode		Feedforward compensation				Resolution 0~100% (set resolution 1%)
					Positioning completion width				1~655,335 instruction units (set resolution to 1 instruction unit)
					Min setting time				5ms (no load, from rated speed to positioning completion)
Input/output signal			Digital input port		Funtional Location available				Fault reset, forward drive disable, reverse drive disable, forward inch, backward inch, electronic gear ratio switching etc.
			Digital output		Funtional Location available				Servo ready, brake output, motor rotation output, zero-speed signal, torque limit, rotating speed limit, warning output, fault output etc.
Built-in function			Over-travel prevention function						Stopped immediately when P-OT and N-OT are activated.
			Electronic gear ratio						1.0 ≤ B/A ≤ 64000.0
			Protective Function						Over-voltage, under-voltage, over-speed, overheat, overload, over-speed, over-tem- perature, encoder fault, braking resistor overload fault, EEPROM fault, abnormal communication etc.
			Alarm data tracking function						Record 4 groups of historical alarms and relevant data
			RS232 communication						Status display, user parameter setting, monitoring display, alarm tracking display, JOG operation and automatic adjustment operation, speed instruction signal etc.

Installation Instructions

Item	Description
Antirust treatment	Before installation, please wipe off the "rust inhibitor" on the extension of the servo motor shaft before relevant antirust treatment.
Notes for encoders	•The shaft extension shall not be impact during installation, otherwise the encoder inside will be cracked.
Pulley installation	•When installing pulleys on a servo motor shaft with a keyway, use screw holes at the shaft end. In order to install the pulley, first insert the double-headed nail into the screw hole of the shaft, use a washer on the surface of the coupling end, and gradually fasten the pulley with a nut.
	•For servo motor shaft with a keyway, install it with the screw hole at shaft end. For a shaft without keyway, wear coupling or similar methods can be adopted.
	•When the pulley is removed, a pulley remover should be used to prevent impact on the bearing.
	•In order to ensure safety, a protective cover or similar device shall be installed in the rotating area.
Centering	•Please use a coupling to connect the device with the machine and keep the axis of the servo motor in a straight line with that of the machinery. The radial runout of the coupling should not be greater than 0.03 mm. If centering is not sufficient, vibration will occur, which may damage bearings, encoders, etc.
Installation direction	•Servo motor can be installed in a horizontal or vertical direction. Please do not install the device obliquely, otherwise it may cause wearing of motor bearing.
Countermeasures for oil and water	For use in places with water dripping, please confirm the protection rating of the servo motor before use (except the shaft penetration part). For use in places where oil drips to the shaft penetration part, please be sure to use servo motors with oil seals.
	Service conditions for servo motors with oil seals:
	•Please make sure that the oil level is lower than the lip of the oil seal during use.
	•Please use the oil seal in a state where the oil spatter can be kept in a good degree.
	•When the servo motor is installed vertically upward, please be careful to prevent oil accumulation on the oil seal lip.
Cable stress condition	Do not bend the cables excessively or apply tension to them, especially for the 0.14 mm^2 or 0.2 mm^2 core wires of the encoder signal cables, which is very thin. So please do not stretch them too tightly during wiring and use.When installing in the tow chain, high-flexibility tow chain cables must be selected.
Connector handling	For the connector part, please pay attention to the following:
	•When connecting a connector, please make sure that there is no foreign matter such as garbage or metal debris in the connector.
	•When connecting the connector to the servo motor, be sure to connect from the side of the main circuit cable of the servo motor first, and the main cable must be reliably grounded. Otherwise, the encoder may fail due to the potential difference with PE.
	•When wiring, please make sure the pins are arranged correctly.
	•The connector is made of resin. Do not apply impact to the connector, otherwise it may be damaged.
	•Always hold the main body of the servo motor during handling while the cables remain connected. Otherwise, the connector may be damaged or the cables may be broken.
	•If a cable needs to be bent, due care should be taken during wiring so as not to cause pressure or tension on the connector, otherwise damage or poor contact of the connector may be caused.

 

Company Profile